Overview
| CODE | REASON | EFFECT |
| Fault Code: 3596 PID: SPN: 4334 FMI: 2/2 LAMP: Amber SRT: |
The diesel exhaust fluid pressure sensor has reported a reading too high or low for the operating conditions.
|
Possible reduced engine performance. |
Circuit Description
The Engine Control Module (ECM) provides a 5 volt supply and a ground to the aftertreatment diesel exhaust fluid pressure sensor. The pressure sensor provides a signal to the ECM on the sensor signal circuit. This sensor signal voltage changes, based on the aftertreatment diesel exhaust fluid pressure supplied by the dosing unit. The ECM will detect a low signal voltage at low diesel exhaust fluid pressures, and a high signal voltage at high diesel exhaust fluid pressures.
Component Location
The aftertreatment diesel exhaust fluid pressure sensor is internal to the aftertreatment diesel exhaust fluid dosing unit and can not be serviced separately.
Conditions for Running the Diagnostics
This diagnostic runs when diesel exhaust fluid dosing unit is fully primed, and is actively maintaining diesel exhaust fluid pressure in the dosing system.
Conditions for Setting the Fault Codes
The diesel exhaust fluid dosing unit was unable to maintain the commanded diesel exhaust fluid pressure.
Action Taken When the Fault Code is Active
- The ECM illuminates the amber CHECK ENGINE lamp and/or the malfunction indicator lamp (MIL) immediately when the diagnostic runs and fails.
Engine torque will be reduced if the engine is operated for an extended period of time with this fault active.
Conditions for Clearing the Fault Code
- To validate the repair, perform the «Aftertreatment Diesel Exhaust Fluid Doser Pump Override Test» found under «ECM Diagnostic Tests» in the recommended Cummins® electronic service tool or equivalent.
- The fault code status displayed by the recommended Cummins® electronic service tool or equivalent will change to INACTIVE immediately after the diagnostic runs and passes.
- The ECM will turn off the amber CHECK ENGINE lamp immediately after the diagnostic runs and passes.
- For On-Board Diagnostics (OBD) engines, the ECM will extinguish the Malfunction Indicator Lamp (MIL) after three consecutive trips where the diagnostic runs and passes.
- The “Reset All Faults” command in the recommended Cummins® electronic service tool or equivalent can be used to clear active and inactive faults, as well as extinguish the MIL for OBD applications.
Shop Talk
Possible causes of this fault code include:
Leaking diesel exhaust fluid lines
Malfunctioning diesel exhaust fluid dosing unit
Blocked or restricted diesel exhaust fluid dosing unit supply line fitting
Blocked or restricted diesel exhaust fluid filters
Malfunctioning diesel exhaust fluid pressure sensor
Malfunctioning diesel exhaust fluid controller.
Reference the appropriate OEM wiring diagram when troubleshooting circuits that utilize wiring supplied by the OEM.
For intermittent power supply and datalink communication issues with Aftertreatment Components, it is highly recommended that the OEM Power Distribution Center fuses and relays be thoroughly checked for loose, missing or intermittent connections.
Troubleshooting Summary
- Check for primary fault codes
- Aftertreatment diesel exhaust fluid dosing unit is malfunctioning
- Aftertreatment diesel exhaust fluid dosing unit pressure sensor is malfunctioning
- Aftertreatment diesel exhaust fluid dosing unit open circuit check
- Aftertreatment diesel exhaust fluid dosing unit connector is malfunctioning
- Aftertreatment diesel exhaust fluid dosing unit line or fittings are cracked, plugged or restricted
- Aftertreatment diesel exhaust fluid is contaminated
- Aftertreatment diesel exhaust fluid dosing unit suction test
- Aftertreatment diesel exhaust fluid dosing unit is malfunctioning
- Aftertreatment diesel exhaust fluid dosing unit intake restriction
- Air in the aftertreatment diesel exhaust fluid
- Aftertreatment Diesel Exhaust Fluid Doser Pump Override test
- Aftertreatment diesel exhaust fluid dosing valve is malfunctioning
- ECM calibration revision history check
- Aftertreatment diesel exhaust fluid controller is malfunctioning
Solution: S00001402
Verification
Conditions
- Turn keyswitch ON.
- Connect the recommended Cummins® electronic service tool or equivalent.
Action
- Use the recommended Cummins® electronic service tool or equivalent to read the fault codes.
Specification
Before troubleshooting this fault code, troubleshoot any fault code that is active or has more than one inactive count within the last 25 engine operating hours from the following list:
- Sensor supply 5: 1695, 1696
- Aftertreatment diesel exhaust fluid system: 3571, 3572
Linked Solutions
- None
Repair
- Perform a search on the appropriate fault codes.
Validation
- None
Solution: S00011152
Verification
Conditions
- Turn keyswitch ON.
- Connect the recommended Cummins® electronic service tool or equivalent.
Action
- Use the recommended Cummins® electronic service tool or equivalent to read the snapshot data for the fault code.
Monitor the following parameters:
- Aftertreatment diesel exhaust fluid dosing unit state.
Specification
- If the aftertreatment diesel exhaust fluid dosing unit state parameter does not display «Dosing» or «Purging» in the fault code snapshot data, then proceed to the Linked Solutions section.
Linked Solutions
- Aftertreatment diesel exhaust fluid dosing unit pressure sensor is malfunctioning
- Aftertreatment diesel exhaust fluid dosing unit open circuit check
Repair
- No additional action is required for this solution.
Validation
- None
Solution: S00003265
Verification
Conditions
- Turn keyswitch OFF.
- Disconnect the aftertreatment diesel exhaust fluid dosing valve supply line from the aftertreatment diesel exhaust fluid dosing valve and secure it appropriately.
- Turn keyswitch ON.
- Connect the recommended Cummins® electronic service tool or equivalent.
Action
- Use the recommended Cummins® electronic service tool or equivalent.
- Monitor the aftertreatment diesel exhaust fluid pressure.
Specification
- A malfunctioning aftertreatment diesel exhaust fluid pressure sensor has been detected if the reading is not within the following specification: 0 ± 69 kpa [0 ± 10 psi]
Linked Solutions
- None
Validation
- Connect all components
- Connect the recommended Cummins® electronic service tool or equivalent.
- Disable the fault code.
- Operate the engine within the «Conditions for Clearing the Fault Code» found in the Overview section of the troubleshooting procedure.
- Verify that the fault code is no longer active.
- Check ECM Calibration Revision History
- Use the recommended Cummins® electronic service tool or equivalent to find the current ECM code and revision number in the ECM.
- Compare the ECM code and revision number in the ECM to the calibration revisions listed in the ECM Calibration Revision History Database for applicable changes related to this fault code.
- Refer to ECM Calibration Revision History Database.
Solution: S00011153
Verification
Conditions
- Turn keyswitch OFF.
- Disconnect the aftertreatment diesel exhaust fluid controller wiring harness 86-pin connector from the aftertreatment diesel exhaust fluid controller.
- Disconnect the aftertreatment diesel exhaust fluid dosing unit from the OEM wiring harness.
Action
- Inspect the pins and connectors for damage.
- Measure the resistance between the aftertreatment diesel exhaust fluid dosing unit SUPPLY pin at the aftertreatment diesel exhaust fluid dosing unit harness connector and the aftertreatment diesel exhaust fluid dosing unit SUPPLY pin of the aftertreatment diesel exhaust fluid controller harness 86-pin connector.
- Measure the resistance between the aftertreatment diesel exhaust fluid dosing unit RETURN pin at the aftertreatment diesel exhaust fluid dosing unit wiring harness connector and the aftertreatment diesel exhaust fluid dosing unit RETURN pin of the aftertreatment diesel exhaust fluid controller wiring harness 86-pin connector.
- Measure the resistance between the aftertreatment diesel exhaust fluid dosing unit SIGNAL pin at the aftertreatment diesel exhaust fluid dosing unit harness connector and the aftertreatment diesel exhaust fluid dosing unit SIGNAL pin of the aftertreatment diesel exhaust fluid controller harness 86-pin connector.
- Refer to the circuit diagram or wiring diagram for connector pin identification.
Specification
- A malfunctioning aftertreatment diesel exhaust fluid controller harness has been detected if the resistance is greater than the following specification: 10 Ω
- A malfunctioning aftertreatment diesel exhaust fluid controller has been detected if the resistance is less than the following specification: 10 Ω
Linked Solutions
- None
Repair
Repair or replace only the components that were found to be out of specification.
- Repair or replace aftertreatment diesel exhaust fluid controller wiring harness.
Refer to OEM Service Manual
- Replace aftertreatment diesel exhaust fluid controller.
Validation
- Connect all components
- Connect the recommended Cummins® electronic service tool or equivalent.
- Disable the fault code.
- Operate the engine within the «Conditions for Clearing the Fault Code» found in the Overview section of the troubleshooting procedure.
- Verify that the fault code is no longer active.
- Check ECM Calibration Revision History
- Use the recommended Cummins® electronic service tool or equivalent to find the current ECM code and revision number in the ECM.
- Compare the ECM code and revision number in the ECM to the calibration revisions listed in the ECM Calibration Revision History Database for applicable changes related to this fault code.
- Refer to ECM Calibration Revision History Database.
Solution: S00002928
Verification
Conditions
- Turn keyswitch OFF.
- Disconnect the aftertreatment diesel exhaust fluid dosing unit from the OEM wiring harness.
Action
- Inspect the pins and connectors for damage.
- Inspect all connections for corrosion or loose connections.
Specification
- If the aftertreatment diesel exhaust fluid dosing unit connector or the aftertreatment diesel exhaust fluid dosing unit wiring harness connector show signs of diesel exhaust fluid, then a malfunctioning aftertreatment diesel exhaust fluid dosing unit connector has been detected.
Linked Solutions
- None
Repair
Repair or replace only the components that were found to be out of specification.
- Replace aftertreatment diesel exhaust fluid dosing unit.
Validation
- Connect all components
- Connect the recommended Cummins® electronic service tool or equivalent.
- Disable the fault code.
- Operate the engine within the «Conditions for Clearing the Fault Code» found in the Overview section of the troubleshooting procedure.
- Verify that the fault code is no longer active.
- Check ECM Calibration Revision History
- Use the recommended Cummins® electronic service tool or equivalent to find the current ECM code and revision number in the ECM.
- Compare the ECM code and revision number in the ECM to the calibration revisions listed in the ECM Calibration Revision History Database for applicable changes related to this fault code.
- Refer to ECM Calibration Revision History Database.
Solution: S00000664
Verification
Conditions
- Turn keyswitch OFF.
Action
- Verify the lines are not swapped at the dosing unit, dosing valve or diesel exhaust fluid tank connections.
- Visually inspect the aftertreatment diesel exhaust fluid tank connections for cracks or pitting.
- Visually inspect the aftertreatment diesel exhaust fluid tank vent line for restrictions.
- Visually inspect the aftertreatment diesel exhaust fluid line for damage.
- Visually inspect both dosing unit connections and fittings for loose, leaking, or damaged connections.
- Disconnect the suction line and pressure line dosing unit connectors and look for signs of build-up or blockage.
- Inspect the aftertreatment diesel exhaust fluid dosing unit inlet connector screen.
- Visually inspect the suction line for signs of leakage or openings which will allow the dosing unit to suck in air with the diesel exhaust fluid.
- Visually inspect the pressure line for signs of leakage or rupture.
- Verify proper sealing at all connection points, including diesel exhaust fluid tank, dosing unit, and dosing valve.
Specification
- If there are aftertreament diesel exhaust fluid lines reversed, damaged, leaking or restricted connections found, then proceed to the Repair section.
Linked Solutions
- None
Repair
- Repair or replace damaged components.
Refer to OEM Service Manual
- Replace the aftertreatment diesel exhaust fluid dosing unit inlet connector screen.
Validation
- Connect all components
- Connect the recommended Cummins® electronic service tool or equivalent.
- Disable the fault code.
- Operate the engine within the «Conditions for Clearing the Fault Code» found in the Overview section of the troubleshooting procedure.
- Verify that the fault code is no longer active.
- Check ECM Calibration Revision History
- Use the recommended Cummins® electronic service tool or equivalent to find the current ECM code and revision number in the ECM.
- Compare the ECM code and revision number in the ECM to the calibration revisions listed in the ECM Calibration Revision History Database for applicable changes related to this fault code.
- Refer to ECM Calibration Revision History Database.
Solution: S00000563
Verification
Conditions
- Turn keyswitch OFF.
Action
- Inspect the aftertreatment diesel exhaust fluid in the tank for signs of debris or contamination.
- Use a diesel exhaust fluid refractometer to measure the concentration of the diesel exhaust fluid in the tank.
Specification
- If there are signs of contaminates in the aftertreatment diesel exhaust fluid, then proceed to the Repair section.
Linked Solutions
- None
Repair
- Drain the diesel exhaust fluid tank, clean thoroughly and refill with pure diesel exhaust fluid.
Validation
- Connect all components
- Connect the recommended Cummins® electronic service tool or equivalent.
- Disable the fault code.
- Operate the engine within the «Conditions for Clearing the Fault Code» found in the Overview section of the troubleshooting procedure.
- Verify that the fault code is no longer active.
- Check ECM Calibration Revision History
- Use the recommended Cummins® electronic service tool or equivalent to find the current ECM code and revision number in the ECM.
- Compare the ECM code and revision number in the ECM to the calibration revisions listed in the ECM Calibration Revision History Database for applicable changes related to this fault code.
- Refer to ECM Calibration Revision History Database.
Solution: S00000360
Verification
Conditions
- Turn keyswitch ON.
- Connect the recommended Cummins® electronic service tool or equivalent.
Action
- Perform the Aftertreatment Diesel Exhaust Fluid Dosing Unit Suction Test.
Specification
- If the vacuum in diagnostic line does not meet specification, then proceed to the Linked Solutions section.
Linked Solutions
Click on the link below:
- Aftertreatment diesel exhaust fluid dosing unit is malfunctioning
Repair
- No additional action is required for this solution.
Validation
- Connect all components
- Connect the recommended Cummins® electronic service tool or equivalent.
- Disable the fault code.
- Operate the engine within the «Conditions for Clearing the Fault Code» found in the Overview section of the troubleshooting procedure.
- Verify that the fault code is no longer active.
- Check ECM Calibration Revision History
- Use the recommended Cummins® electronic service tool or equivalent to find the current ECM code and revision number in the ECM.
- Compare the ECM code and revision number in the ECM to the calibration revisions listed in the ECM Calibration Revision History Database for applicable changes related to this fault code.
- Refer to ECM Calibration Revision History Database.
Solution: S00000522
Verification
Conditions
- Turn keyswitch OFF.
Action
- Perform the Aftertreatment Diesel Exhaust Fluid Dosing Unit Non Air Flush.
- Perform the Aftertreatment Diesel Exhaust Fluid Dosing Unit Suction Test.
Specification
- If the Aftertreatment Diesel Exhaust Fluid Dosing Unit Non Air Flush does not meet specifciation, then proceed to the Repair section.
- If the Aftertreatment Diesel Exhaust Fluid Dosing Unit Suction Test does not meet specification, then proceed to the Repair section.
Linked Solutions
- None
Repair
Repair or replace only the components that were found to be out of specification.
- Cleaning of the aftertreatment diesel exhaust fluid dosing system resolved the issue.
- Replace aftertreatment diesel exhaust fluid dosing unit.
Validation
- Connect all components
- Connect the recommended Cummins® electronic service tool or equivalent.
- Disable the fault code.
- Operate the engine within the «Conditions for Clearing the Fault Code» found in the Overview section of the troubleshooting procedure.
- Verify that the fault code is no longer active.
- Check ECM Calibration Revision History
- Use the recommended Cummins® electronic service tool or equivalent to find the current ECM code and revision number in the ECM.
- Compare the ECM code and revision number in the ECM to the calibration revisions listed in the ECM Calibration Revision History Database for applicable changes related to this fault code.
- Refer to ECM Calibration Revision History Database.
Solution: S00000732
Verification
Conditions
- Turn keyswitch ON.
- Connect the recommended Cummins® electronic service tool or equivalent.
Action
- Check the aftertreatment diesel exhaust fluid dosing unit intake restriction.
Specification
- If the vacuum in diagnostic line is not within specification, then proceed to the Repair section.
Linked Solutions
- None
Repair
Repair or replace only the components that were found to be out of specification.
- Replace the diesel exhaust fluid tank filter.
Refer to OEM Service Manual
- Clean or replace the aftertreatment diesel exhaust fluid intake line.
Refer to OEM Service Manual
- Clean or replace the aftertreatment diesel exhaust fluid tank header.
Refer to OEM Service Manual
- Clean or replace the aftertreatment diesel exhaust fluid tank vent.
Refer to OEM Service Manual
Validation
- Connect all components
- Connect the recommended Cummins® electronic service tool or equivalent.
- Disable the fault code.
- Operate the engine within the «Conditions for Clearing the Fault Code» found in the Overview section of the troubleshooting procedure.
- Verify that the fault code is no longer active.
- Check ECM Calibration Revision History
- Use the recommended Cummins® electronic service tool or equivalent to find the current ECM code and revision number in the ECM.
- Compare the ECM code and revision number in the ECM to the calibration revisions listed in the ECM Calibration Revision History Database for applicable changes related to this fault code.
- Refer to ECM Calibration Revision History Database.
Solution: S00000730
Verification
Conditions
- Turn keyswitch ON.
Specification
- If a line, fitting, connection, or dosing unit is leaking, then a malfunction has been detected in the aftertreatment diesel exhaust fluid system or dosing unit.
Linked Solutions
- None
Validation
- Connect all components
- Connect the recommended Cummins® electronic service tool or equivalent.
- Disable the fault code.
- Operate the engine within the «Conditions for Clearing the Fault Code» found in the Overview section of the troubleshooting procedure.
- Verify that the fault code is no longer active.
- Check ECM Calibration Revision History
- Use the recommended Cummins® electronic service tool or equivalent to find the current ECM code and revision number in the ECM.
- Compare the ECM code and revision number in the ECM to the calibration revisions listed in the ECM Calibration Revision History Database for applicable changes related to this fault code.
- Refer to ECM Calibration Revision History Database.
Solution: S00002761
Verification
Conditions
- Reconnect all aftertreatment diesel exhaust fluid lines and electrical connectors to the dosing unit and aftertreatment diesel exhaust fluid tank if they have been previously disconnected during troubleshooting.
Action
- Remove the aftertreatment diesel exhaust fluid dosing valve from the decomposition tube.
- Turn keyswitch ON.
- Connect the recommended Cummins® electronic service tool or equivalent.
- Use the recommended Cummins® electronic service tool or equivalent.
- Perform the Aftertreatment Diesel Exhaust Fluid Doser Pump Override Test.
The Aftertreatment Diesel Exhaust Fluid Doser Pump Override test can only be ran twice before a key cycle needs to be performed.
Specification
- If the Aftertreatment Diesel Exhaust Fluid Doser Pump Override Test meets the specification, then proceed to the next solution.
- If the Aftertreatment Diesel Exhaust Fluid Doser Pump Override Test does not meet the specification, then proceed to the Linked Solutions section.
Linked Solutions
Click on the link below:
- Aftertreatment diesel exhaust fluid dosing valve is malfunctioning
Repair
- No additional action is required for this solution.
Validation
- Connect all components
- Connect the recommended Cummins® electronic service tool or equivalent.
- Disable the fault code.
- Operate the engine within the «Conditions for Clearing the Fault Code» found in the Overview section of the troubleshooting procedure.
- Verify that the fault code is no longer active.
- Check ECM Calibration Revision History
- Use the recommended Cummins® electronic service tool or equivalent to find the current ECM code and revision number in the ECM.
- Compare the ECM code and revision number in the ECM to the calibration revisions listed in the ECM Calibration Revision History Database for applicable changes related to this fault code.
- Refer to ECM Calibration Revision History Database.
Solution: S00002764
Verification
Conditions
- Turn keyswitch OFF.
- Connect the recommended Cummins® electronic service tool or equivalent.
Action
- Clean the aftertreatment diesel exhaust fluid dosing valve.
- Turn keyswitch ON.
- Use the recommended Cummins® electronic service tool or equivalent.
- Perform the Aftertreatment Diesel Exhaust Fluid Doser Pump Override Test.
Specification
- If the Aftertreatment Diesel Exhaust Fluid Doser Pump Override Test is not within specification, then proceed to the Repair section.
Linked Solutions
- None
Repair
Repair or replace only the components that were found to be out of specification.
- Replace the aftertreatment diesel exhaust fluid dosing valve.
- Replace aftertreatment diesel exhaust fluid dosing unit.
Validation
- Connect all components
- Connect the recommended Cummins® electronic service tool or equivalent.
- Disable the fault code.
- Operate the engine within the «Conditions for Clearing the Fault Code» found in the Overview section of the troubleshooting procedure.
- Verify that the fault code is no longer active.
- Check ECM Calibration Revision History
- Use the recommended Cummins® electronic service tool or equivalent to find the current ECM code and revision number in the ECM.
- Compare the ECM code and revision number in the ECM to the calibration revisions listed in the ECM Calibration Revision History Database for applicable changes related to this fault code.
- Refer to ECM Calibration Revision History Database.
Solution: S00000443
Verification
Conditions
- Connect all components.
- Turn keyswitch ON.
- Connect the recommended Cummins® electronic service tool or equivalent.
Action
- Use the recommended Cummins® electronic service tool or equivalent to read the fault codes.
- Use the recommended Cummins® electronic service tool or equivalent to find the current ECM code and revision number in the ECM.
- Compare the ECM code and revision number in the ECM to the calibration revision listed in the ECM calibration revision history for applicable changes.
Specification
- If a calibration update for this fault code is available, the ECM calibration revision must be that revision or higher.
Linked Solutions
- None
Repair
- Prior to downloading the ECM calibration, check to see that all job images and all other troubleshooting has been documented as downloading an ECM calibration will remove the fault codes on the ECM.
- Download the updated ECM calibration code.
Validation
- Connect all components
- Connect the recommended Cummins® electronic service tool or equivalent.
- Disable the fault code.
- Operate the engine within the «Conditions for Clearing the Fault Code» found in the Overview section of the troubleshooting procedure.
- Verify that the fault code is no longer active.
- Check ECM Calibration Revision History
- Use the recommended Cummins® electronic service tool or equivalent to find the current ECM code and revision number in the ECM.
- Compare the ECM code and revision number in the ECM to the calibration revisions listed in the ECM Calibration Revision History Database for applicable changes related to this fault code.
- Refer to ECM Calibration Revision History Database.
Solution: S00002906
Verification
Conditions
- None
Action
- Verify all preceding solution verifications for this fault code have been performed.
Specification
- If the fault code is still active after all the preceding solution verifications have been performed, then a malfunctioning aftertreatment diesel exhaust fluid controller has been detected.
Linked Solutions
- None
Validation
- None
If all steps have been completed and no root cause has been identified, then follow the technical escalation process.